Link 1
Stunt Hangar YouTube
P.A.M.P.A.
AMA
Balsa Density Calculator
This topic
This board
Entire forum
Google
Home
Help
Tags
Advertise
Login
Register
News:
---->Stunt News click here<----
May 23, 2024, 08:55:00 AM
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
stunthanger.com
»
Speed,Combat,Scale,Racing
»
Carrier
(Moderator:
Paul Smith
) »
Nelson .15 prop nut
« previous
next »
Print
Pages: [
1
]
Go Down
Author
Topic: Nelson .15 prop nut (Read 1075 times)
Jim Roselle
Guest
Trade Count:
(
0
)
Nelson .15 prop nut
«
on:
July 20, 2017, 11:24:23 PM »
I recently acquired a Nelson .15 for my carrier plane. It's a full ounce heavier than the Norvel it's replacing. I'd like to replace the heavy prop nut that's on it with a more traditional nut. Can I just use a standard stainless nut and washer?
Logged
Wayne J. Buran
AMA Member
Trade Count:
(
0
)
Admiral
Posts: 1096
Re: Nelson .15 prop nut
«
Reply #1 on:
July 21, 2017, 04:52:39 AM »
Jim, I don't know the size used on a Nelson however once you figure that out I don't see why not. Make sure the washer has the correct inside diameter so it doesn't sit off center.
Wayne
Logged
Wayne Buran
Medina, Ohio
AMA 14986 CD
USAF Veteran 35 TAC GP/ 6236 CSG, DonMuang RTAFB, Bangkok, Thailand 65-66 North Coast Controliners "A fine is a tax for doing wrong. A tax is a fine for doing well!
eric david conley
Trade Count:
(
0
)
Captain
Posts: 499
Re: Nelson .15 prop nut
«
Reply #2 on:
July 21, 2017, 11:10:25 AM »
By chance will the nut and washer from the Norvel work on the Nelson or perhaps it is metric?
Logged
Eric
Jim Roselle
Guest
Trade Count:
(
0
)
Re: Nelson .15 prop nut
«
Reply #3 on:
July 21, 2017, 02:14:41 PM »
Quote from: eric david conley on July 21, 2017, 11:10:25 AM
By chance will the nut and washer from the Norvel work on the Nelson or perhaps it is metric?
The norvel has a stud that screws into the crankshaft.
What % nitro are you guys running in these little beasts?
Logged
eric david conley
Trade Count:
(
0
)
Captain
Posts: 499
Re: Nelson .15 prop nut
«
Reply #4 on:
July 21, 2017, 04:46:35 PM »
I ran 25 percent in mine and had good results. On the other hand I'm pretty sure Burt runs 35 percent in his with outstanding results.
Logged
Eric
Paul Smith
Moderator
Trade Count:
(
0
)
Admiral
Posts: 5807
Re: Nelson .15 prop nut
«
Reply #5 on:
July 22, 2017, 09:26:55 AM »
The Nelson uses a US standard 1/4" stud. Pre-much any standard prop nut will work.
Logged
Paul Smith
Advertise Here
Print
Pages: [
1
]
Go Up
« previous
next »
Tags:
stunthanger.com
»
Speed,Combat,Scale,Racing
»
Carrier
(Moderator:
Paul Smith
) »
Nelson .15 prop nut
Advertise Here