News:

 

CLICK HERE--><--CLICK HERE

Stalker Stunt Engines

Started by Ruslan Kurenkov, December 29, 2018, 02:55:52 PM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

Ruslan Kurenkov

Hello, friends !
Congratulations on your upcoming New Year!
I want to wish you all a good mood and a lot of good flights in 2019.
Controllineparts will do its best to ensure that your flights on our lines and engines are successful and bring you only positive emotions.
I want to invite you to discuss all questions about the use of different Stalker stunt engines in this particular special topic.
I want to invite you to ask here any questions on the selection of the stunt engine for your aircraft, on the technical parameters and installation sizes of various Stalker engines, on installing the correct propeller size on your engine and on the fuel composition, on using the correct type of glow plugs and providing spare parts.
I will be happy to answer all your questions and will gladly take part in the discussion of all issues related to the repair and maintenance of the stunt engine Stalker.
Today we have in stock more than 10 Stalker, varying in size and location of the engine muffler, from the smallest 0.40 to the most powerful 0.81. I think that such a wide range of stunt engines will be able to satisfy both the novice and professional pilot. We also provide full technical support to our customers and the provision of any spare parts for our engines.

Regards
Ruslan Kurenkov

Dennis Saydak

Hello RK and best wishes for the new year. Can you provide any information on the long stroke .61 version. Does anyone use it?
Just when you think you're getting ahead in the rat race.....you find the rats just get faster!

Randy Cuberly

Ruslan,

I have a Stalker 66LS but have so far only run it on the bench.  It seems to be very easy to start and mild mannered.  I am close to finishing an airplane for it but have a question regarding using a tuned pipe with it.

The engine will be used in a GeoXL airplane that is approximately 700 Sq/inch wing area but will be relatively light at approximately 57 ounces.   I have built two of these airplanes in the past so I'm relatively sure of that weight.   

I have used tuned pipes for many years now and like the control that they provide, especially in the wind!

What is your opinion of trying to use a tuned pipe with this engine and  can you provide a header that would function with a tuned pipe?

Thanks,

Randy Cuberly

 


 
Randy Cuberly
Tucson, AZ

Ruslan Kurenkov

Quote from: Dennis Saydak on December 29, 2018, 04:03:52 PM
Hello RK and best wishes for the new year. Can you provide any information on the long stroke .61 version. Does anyone use it?
Hello Dennis!
The long-stroke version of the Stalker 0.61 engine was developed and produced more than 10 years ago. The engine received the designation LT-LS, in contrast to the previous modification LT-EX where the piston diameter was 24 mm and the piston stroke was 22 mm. The piston diameter in the engine Stalker 61 LT-LS is 23 mm and the piston stroke is 24mm. This modification is the most successful and sold than the short-run classic version. On the basis of the Stalker 61 LT-LS engine, the best-selling Stalker company was created - a modification with the number 66, with a diameter and stroke of 24 mm and the designation LT-LS. You can see all the dimensions of the engine in the attachment, they fully coincide with the 66 LT-LS, these engines have a common crankcase.
Australian athletes fly successfully on these engines, perhaps they will share their experience with you.

Regard
Ruslan Kurenkov

Ruslan Kurenkov

Quote from: Randy Cuberly on December 29, 2018, 04:17:36 PM
Ruslan,

I have a Stalker 66LS but have so far only run it on the bench.  It seems to be very easy to start and mild mannered.  I am close to finishing an airplane for it but have a question regarding using a tuned pipe with it.

The engine will be used in a GeoXL airplane that is approximately 700 Sq/inch wing area but will be relatively light at approximately 57 ounces.   I have built two of these airplanes in the past so I'm relatively sure of that weight.   

I have used tuned pipes for many years now and like the control that they provide, especially in the wind!

What is your opinion of trying to use a tuned pipe with this engine and  can you provide a header that would function with a tuned pipe?

Thanks,

Randy Cuberly

 


 

Hi Randy!
I am very glad to hear you.
I used to fly a lot of Stalker 66 with my friend, now two juniors are flying for a few years flying next to Stalker 66. The weather at our workouts is almost always very windy and if a plane weighs less than 60 ounces then no wind is terrible for him. My plane after two repairs scored from 64 ounces to 66 ounces. At the same time, I calmly flew in a very strong wind on my Stalker 66 on thin lines 0.0145 and a wooden two-bladed propeller 13.8/6.3 in (350mm / 160mm)
Initially, this engine was designed by Oleg for operation without the use of a resonant tube and without the use of nitromethane in fuel. Maybe someone used a pipe with this engine but we have not conducted such experiments. I do not know whether it will work with the pipe or not, but I am almost sure that it will not.
It is a pity, but I did not have the opportunity to fly on an airplane with an engine with a resonant tube, and I don't understand absolutely anything in the resonant tubes. To use the resonant tube, Stalker manufactures the K-77 engine (a copy of the PA-75 engine) for Kaz Minato. On these engines at the World Championships in Landres, members of the USA and Japan national teams flew. They are very fond of resonant tubes.

Regards
Ruslan

Randy Cuberly

Hi Ruslan,

Thanks for your reply.  I'm very familiar with the K77 engine you make for Kaz Minato.  I bought one of the first ones that He received from Stalker.  It's a tremendous powerplant.  Perhaps even a little better than the PA 75 (of which I have two).  It's perhaps just a bit less powerful than the PA but it regulates the best in wind of any engine I've flown.
Based on what you've told me I'll probably just use the Stalker 66 with the supplied muffler.

Do you supply a rear mounting ring or rubber device for supporting the muffler, or is it OK to just let it hang from the engine.  That seems a bit risky for the muffler mount of the engine to just allow it to hang on the engine.  I would think vibration would take it's toll on that very quickly.

I would very much appreciate any information you can supply for mounting the muffler!

Thanks for any help you can provide.

Randy Cuberly



Randy Cuberly
Tucson, AZ

Michael Palm

I have a flying buddie that used a pipe on a Stalker 61. He said that the engine is very wide in operation style. Maybe the 66 is like. I dont remember how the set up was. He is not on this forum i think, but he is on facebook and write some time in the control line enthusiast group. His name is Kauko Kainulainen, he is a Finn living in Sweden but he speaks good English. Maybe you can write him there and ask.
R/C is disco, C/L is Rock n Roll

Steve Helmick

Quote from: Randy Cuberly on December 29, 2018, 06:07:14 PM
Hi Ruslan,


Do you supply a rear mounting ring or rubber device for supporting the muffler, or is it OK to just let it hang from the engine.  That seems a bit risky for the muffler mount of the engine to just allow it to hang on the engine.  I would think vibration would take it's toll on that very quickly.

I would very much appreciate any information you can supply for mounting the muffler!

Thanks for any help you can provide.

Randy Cuberly


I have a .76RE and two .51RE's. There is a cast-in "boss" on the back of the mufflers that are supposed to be supported...the exact method escapes me at the moment, but I believe it would fit in a neoprene grommet which could be mounted in a piece of plywood or CF plate.  :) Steve
"The United States has become a place where professional athletes and entertainers are mistaken for people of importance." - Robert Heinlein

In 1944 18-20 year old's stormed beaches, and parachuted behind enemy lines to almost certain death.  In 2015 18-20 year old's need safe zones so people don't hurt their feelings.

Ruslan Kurenkov

Quote from: Randy Cuberly on December 29, 2018, 06:07:14 PM
Hi Ruslan,

Thanks for your reply.  I'm very familiar with the K77 engine you make for Kaz Minato.  I bought one of the first ones that He received from Stalker.  It's a tremendous powerplant.  Perhaps even a little better than the PA 75 (of which I have two).  It's perhaps just a bit less powerful than the PA but it regulates the best in wind of any engine I've flown.
Based on what you've told me I'll probably just use the Stalker 66 with the supplied muffler.

Do you supply a rear mounting ring or rubber device for supporting the muffler, or is it OK to just let it hang from the engine.  That seems a bit risky for the muffler mount of the engine to just allow it to hang on the engine.  I would think vibration would take it's toll on that very quickly.

I would very much appreciate any information you can supply for mounting the muffler!

Thanks for any help you can provide.

Randy Cuberly




Hi Randy!
Thank you for your question. I often have to answer it in correspondence with customers.
The silencer on the engine Stalker is attached to the crankcase with two M3 bolts for an internal hex. Three years ago, our supplier of bolts let us down a little. He sold us a batch of bolts that were very hardened and brittle. After 50-70 flights, one of the two mounting bolts of the muffler necessarily collapsed from constant thermal expansion. After that, we started to pack all our engines with M3 stainless steel bolts only. This steel is not brittle and does not collapse like black hardened bolts. You must replace your black bolts with stainless steel bolts. Between the engine crankcase and muffler housing, apply a thin layer of automotive sealant to repair the engine. The sealant layer should be no more than the thickness of the lines (0.015 inch). You must firmly hold the mounting bolts of the muffler immediately after applying the sealant and be sure to put on the bolt a little blue thread retainer. The silencer on the Stalker 66 is fixed only with two M3 bolts and that's it. The silencer is not attached to the body of the aircraft through a rubber ring as on the Stalker 40. This engine has virtually no vibration. It is perfectly balanced if you use a well-balanced propeller and spiner.
Regards,Ruslan

Quote from: Steve Helmick on December 29, 2018, 11:42:06 PM

I have a .76RE and two .51RE's. There is a cast-in "boss" on the back of the mufflers that are supposed to be supported...the exact method escapes me at the moment, but I believe it would fit in a neoprene grommet which could be mounted in a piece of plywood or CF plate.  :) Steve
Hi Steve !
Thank you for your question. Stalker 76 engines have a silencer mount with only two M3 bolts as I described above for Randy Cuberly.
Engine Stalker 51 has a silencer mount on the thread on which it is screwed to the engine crankcase and tightened with a locking nut. Before connecting to the crankcase, a little automotive sealant should be applied to the thread to repair the engine and then fasten immediately.
Rubber ring to the body of the aircraft is attached only the smallest Stalker 40.

Regards,Ruslan

Chuck_Smith

Good looking stuff. You can definitely see the family resemblance to the K77. The .76 appears to share a lot of the same parts with the K77 such as the venturi, head, thrust washer, etc.

I'm a bit skeptical of the fuel consumption. You're saying the .76  can go six minutes on 100 milliliters? That's less than 3 1/2 ounces. My K77's sure won't do that! They're thirsty beasts on a pipe and I need a little over 8 ounces for a flight.

Still, good stuff and prices look good too. I may have to buy a couple to try them.

Thanks!


Chuck
AMA 76478

Don Jenkins

I built a 64 ounce plane around a Stalker .61 LT-EX.  I got one flip starts, 7 minute runs on 3.75 ounces of 5% nitro with 20% lube (50/50), and a Xoar 13-5 prop.  It pulled great on 64 foot lines and I never had a problem with it until I put into the asphalt, yes destroyed.  However, I purchased a Stalker .66 and I plan on building another Vertigo, but I'll name it something else.  All in all a great engine, and it sounds great too!

Don

Target

Ruslan-
I had thought that there was a .55 in the line up before?

Kind Regards,
Target
Regards,
Chris
AMA 5956

Ruslan Kurenkov

Quote from: Chuck_Smith on December 30, 2018, 04:46:10 AM
Good looking stuff. You can definitely see the family resemblance to the K77. The .76 appears to share a lot of the same parts with the K77 such as the venturi, head, thrust washer, etc.

I'm a bit skeptical of the fuel consumption. You're saying the .76  can go six minutes on 100 milliliters? That's less than 3 1/2 ounces. My K77's sure won't do that! They're thirsty beasts on a pipe and I need a little over 8 ounces for a flight.

Still, good stuff and prices look good too. I may have to buy a couple to try them.

Thanks!


Chuck

Hello Chuck
Thanks for the nice review about my store.
Stalker engines operate at very low revolutions from 7000 to 9000 revolutions per minute with large-diameter propellers. They have a very high torque for this. That is why such a low fuel consumption per flight. It is like a diesel engine in cars. Diesel is denser than gasoline. Methanol fuel for engines Stalker is also denser than the fuel with nitromethane that you use on your K77. This all greatly affects fuel consumption. The work of the motors Stalker is a pronounced 4-2-4 mode in which 70 percent of the engine's operating time is mode 4. For many years of operation, we learned how to adjust our Stalkers and select the propeller pitch so that during horizontal flight the engine works only in mode 4 and This speed of flight in a circle of 5.2-5.3 seconds. When flying at this speed on lines 63-65 feet, the whole complex of flight figures takes 5 minutes and 15 seconds from start-up and at least 6 more laps until the engine stops. A total of 5 minutes and 45 seconds of engine running time per 100ml (less than 4 ounces) of fuel is obtained. Fuel tanks are designed for a full refill of 120 ml of fuel (4.5 ounces). Before starting, we take 15-20 ml of fuel from the fuel tank. Such a small amount of fuel is very easy to place in an aircraft with small fuselage sizes. And at the end of the flight, such a small amount of fuel does not change the location of the center of gravity of the model aircraft and slightly changes the handling. A large amount of fuel for your K77 greatly changes the center of gravity back to the end of the flight and the two intertwining eights at the end of the complex you will perform on a completely different handling plane than a double coup at the beginning of the complex when your tank is full.
Regards,Ruslan

Brett Buck

Quote from: Chuck_Smith on December 30, 2018, 04:46:10 AM
I'm a bit skeptical of the fuel consumption. You're saying the .76  can go six minutes on 100 milliliters? That's less than 3 1/2 ounces.

    In addition to the factors mentioned - it's also generating *much less* shaft HP in level flight, because the propellors you have to use at 8000-ish rpm are much more efficient than those you have on a PA75. You might be getting 30-40% efficiency in level flight with a 13-3.75 at around 11,500, and maybe 50-60% with a 13-6.5 at 8800 or so. That's around half the shaft power for the same airplane speed. Less power = less fuel, add to that some optimization for this range of operating conditions, higher specific output from getting rid of some of the nitro and replacing it with more methanol, and I can easily believe it. Just running it hotter will greatly increase the amount of power released per unit fuel volume, so reduce the fuel consumption.

   You see the same thing on electrics. The governor-type electrics can run almost any prop you want, just dial in the RPM you need. Start with 6" of pitch, and you may wind up with 30% of your battery capacity left. Change to 3.5" of the same type, spin it up much faster to get the same lap time, and you may be down at 5% of your battery left, or less.

     Look at 4-strokes, they are down in this area in similar conditions, and have a slight improvement in the scavenging and run at nearly optimal mixture ratio (much hotter), with similar high-pitch props and it's 3 1/2 ounces or less, even with 20% nitro.

    You are counting on this very low efficiency in normal flight for the PA or other similar system (which can use up to about 8.5 ounces when you set it up like David's), the system absolutely requires it in order to maintain the speed in corners. As the airplane slows down, the propellor efficiency greatly increases, inhibiting the speed loss, and additionally, driving the pipe closer to resonance, causing the torque to go up as the increased prop load slows the engine down. Same thing if you speed up (like from whip-up), the efficiency drops drastically, at least causing no additional speed increase, if not trying to help slow you down. At the 2003 NATs, in the 30 mph wind, my PA sounded like it was 16-stroking at the bottom of the maneuvers, it was so unloaded (far less than static) to the point I thought it was going to quit.   Unfortunately it did the same thing coming around upwind, for the same reason...

     Point being that for competitive systems, particularly large ones, you are running them in terribly inefficient ways - dead rich/low temperature/low amount of energy released per unit fuel volume, extremely inefficient propellors, with reduced fuel energy density. And frequently, running gigantic engines on relatively small airplanes where you have to figure out how to get rid of huge amounts of excess power. David Fitzgerald's airplane is *smaller than a Thunderbird* and he is running it on a piped 75 - you better do something to make it very inefficient! Fly the same airplane with a 40VF, it will probably fly just about as well, and set up the way we started out, you might be running as little a 4.5 ounces (like I was doing with a similar airplane as recently as the 98 NATs), and that is with 10% nitro and a very inefficient prop.

   So I wouldn't dispute that this could be done on even less fuel with a more efficient prop and higher specific energy fuel, in fact, it seems like about right to me and about what I would expect. I will reserve judgement on the relative in-flight performance and ability to get scores in a stunt contest in the year 2019, but I think we already did very similar experiment to end up where we have.

     Brett

Ruslan Kurenkov

Quote from: Don Jenkins on December 30, 2018, 07:28:13 AM
I built a 64 ounce plane around a Stalker .61 LT-EX.  I got one flip starts, 7 minute runs on 3.75 ounces of 5% nitro with 20% lube (50/50), and a Xoar 13-5 prop.  It pulled great on 64 foot lines and I never had a problem with it until I put into the asphalt, yes destroyed.  However, I purchased a Stalker .66 and I plan on building another Vertigo, but I'll name it something else.  All in all a great engine, and it sounds great too!

Don

Hello Don
You build very beautiful airplanes. I liked the one in the photo. It is a pity that you crashed your plane. It is a pity that the engine was also destroyed. You had one of the first engines Stalker. With the engine 61 LT-EX began the history of the company Stalker 15 years ago. Now in the production company Stalker 11 different engines. The stalker 66 that you purchased to replace the 61st engine is a very good choice. Crankcase dimensions are exactly the same and weight too. Only the propeller will need a little more. Not 330-340 mm in diameter, but 350 mm., And the screw pitch is not 150 mm and 160 mm.
The flight time you wrote it is actually exactly like that. For Stalker 61 fuel tank per 100 ml is enough for 7 minutes of work. For Stalker 66 this volume is enough for 6 minutes 30 seconds.
You wrote that you use fuel with 20 percent lubricant. This is a lot. We strongly recommend using 16 percent 50/50 grease. With this amount of lubricant (16%), you increase by 4 percent the amount of methanol in the fuel. It is methanol that cools your engine and it is methanol that gives you power. My Stalker 66 with 20 percent of the lubricant was always very hot due to the lack of cooling from methanol. When overheating all the time there was a deposit on the piston which acts like an abrasive on your cylinder and wears it quickly. This is exactly the case.
I wish you to quickly build a new aircraft for the Stalker 66.

Regards,Ruslan

Randy Cuberly

Ruslan,

Thank you very much for the information on mounting the muffler.  Actually that is the exact information I was hoping for.

Steve H.  Thanks to you also for the info about the possibility of using a molded ring at the end of the muffler.  That is really what I was expecting to have to do but I'm very happy to hear that it is considered unnecessary on the 66.

Randy Cuberly
Randy Cuberly
Tucson, AZ

M Spencer

This is underway for the Stalker 76 & Stalker 66 . Likely the 66 will do . How many 66 were built with the ' 61 ' case stamped ' 66 ' ??



The VERTIGO engine bay picture , V cunning . Tried to fiind a picture of an auto - Spring / Saddle Ex Mount .
Basically the sping loops over ' the pipe ' onto hooks . Holding it on ' the sddle ' till the diff knocks it down .
As it goes under the rear axle . To eliminate supurflous bends . Olde 250 GT ferroary like . Like Yours .

The thing was , it allowed longitudeinal expansion ( with heat ) , and allowed for a ' Q.D. Exhaust . For getting at other things quick .

Now we know .  :-\  :-\ Just a thought , for if you ARE going to support it .

---------------------------------------------------------------------------------------------------------------------------------------------------

Steve Helmick

Quote from: Randy Cuberly on December 30, 2018, 08:34:34 PM
Ruslan,

Thank you very much for the information on mounting the muffler.  Actually that is the exact information I was hoping for.

Steve H.  Thanks to you also for the info about the possibility of using a molded ring at the end of the muffler.  That is really what I was expecting to have to do but I'm very happy to hear that it is considered unnecessary on the 66.

Randy Cuberly

Ruslan surprised me on that. I'm pretty sure that at least some of the (3) Stalker mufflers I have has a round thingy cast onto the rear of the muffler for that purpose. Or so I was told by Stalker users. 

Most the guys I've seen with the screw-on .51 muffler had problems with the threads seizing or galling, so they installed the muffler once, permanently, and then cut the "header" tube roughly in half and spliced it back on with a bit of silicon hose normally used for tuned pipes...in case anybody in the SH reader group has one. Locally, the .51 has more history and fans than the other Stalkers.   y1 Steve
"The United States has become a place where professional athletes and entertainers are mistaken for people of importance." - Robert Heinlein

In 1944 18-20 year old's stormed beaches, and parachuted behind enemy lines to almost certain death.  In 2015 18-20 year old's need safe zones so people don't hurt their feelings.

Ruslan Kurenkov

Quote from: Target on December 30, 2018, 08:50:13 AM
Ruslan-
I had thought that there was a .55 in the line up before?

Kind Regards,
Target
Hello Target
The company Stalker never produced engines with the designation .55
Regards,Ruslan

Quote from: Motorman on December 30, 2018, 12:58:21 PM
Why don't you make an .049.
Hello Motormen
I think it would be very good if the Stalker company produced 0.49 engines. It is a pity, but now there is only model 0.51 in production. It seems to me that this is not a big difference for you!
Regards,Ruslan
Quote from: Matt Spencer on December 30, 2018, 08:36:38 PM
This is underway for the Stalker 76 & Stalker 66 . Likely the 66 will do . How many 66 were built with the ' 61 ' case stamped ' 66 ' ??
The VERTIGO engine bay picture , V cunning . Tried to fiind a picture of an auto - Spring / Saddle Ex Mount .
Basically the sping loops over ' the pipe ' onto hooks . Holding it on ' the sddle ' till the diff knocks it down .
As it goes under the rear axle . To eliminate supurflous bends . Olde 250 GT ferroary like . Like Yours .

The thing was , it allowed longitudeinal expansion ( with heat ) , and allowed for a ' Q.D. Exhaust . For getting at other things quick .

Now we know .  :-\  :-\ Just a thought , for if you ARE going to support it .

---------------------------------------------------------------------------------------------------------------------------------------------------
Hello Matt
Is your new aircraft in the photo a copy of a real airplane? Very interesting project. I already wrote earlier that the Stalker 66 engine is a modified version of the 61 LT-LS engine whose piston diameter was increased from 23 mm to 24 mm. External dimensions and weight of the engine have not changed. These two engines differ only in the inscriptions on the crankcase. Some questions that you ask me are not clear. I find it hard to translate your Australian English correctly. I am not a very experienced translator.
Regards,Ruslan
Quote from: Steve Helmick on December 30, 2018, 08:55:21 PM
Ruslan surprised me on that. I'm pretty sure that at least some of the (3) Stalker mufflers I have has a round thingy cast onto the rear of the muffler for that purpose. Or so I was told by Stalker users. 
Most the guys I've seen with the screw-on .51 muffler had problems with the threads seizing or galling, so they installed the muffler once, permanently, and then cut the "header" tube roughly in half and spliced it back on with a bit of silicon hose normally used for tuned pipes...in case anybody in the SH reader group has one. Locally, the .51 has more history and fans than the other Stalkers.   y1 Steve

Hello Steve
Silencers to Stalker engines .40 / .46 / .51 have the same parts of the middle part and the backs with an exhaust pipe where there is a protrusion for attaching the muffler to the body of the aircraft. This is done to reduce production. That is why you and your friends thought that all these silencers should be attached to the fuselage of the aircraft through an additional support with a rubber stop.
But only the Stalker .40 engine must necessarily have such an additional mount because it has a free (not rigid) mount of the muffler to the engine crankcase. You are also absolutely right that you can use a silicone pipe to connect the engine crankcase .40 / .46 / .51 with a silencer as on engines that work with a resonant tube. To do this, it is necessary to slightly modify the engine and muffler parts. This is a personal matter for each pilot to change or improve the design of the exhaust system for his particular model of aircraft and for the convenience of access to the fuel tank. But you should know that additional attachment of the silencer to the aircraft fuselage is necessarily necessary only for the Stalker engine .40
Regards,Ruslan

Don Jenkins

Quote from: Ruslan Kurenkov on December 30, 2018, 02:16:08 PM
Hello Don
You build very beautiful airplanes. I liked the one in the photo. It is a pity that you crashed your plane. It is a pity that the engine was also destroyed. You had one of the first engines Stalker. With the engine 61 LT-EX began the history of the company Stalker 15 years ago. Now in the production company Stalker 11 different engines. The stalker 66 that you purchased to replace the 61st engine is a very good choice. Crankcase dimensions are exactly the same and weight too. Only the propeller will need a little more. Not 330-340 mm in diameter, but 350 mm., And the screw pitch is not 150 mm and 160 mm.
The flight time you wrote it is actually exactly like that. For Stalker 61 fuel tank per 100 ml is enough for 7 minutes of work. For Stalker 66 this volume is enough for 6 minutes 30 seconds.
You wrote that you use fuel with 20 percent lubricant. This is a lot. We strongly recommend using 16 percent 50/50 grease. With this amount of lubricant (16%), you increase by 4 percent the amount of methanol in the fuel. It is methanol that cools your engine and it is methanol that gives you power. My Stalker 66 with 20 percent of the lubricant was always very hot due to the lack of cooling from methanol. When overheating all the time there was a deposit on the piston which acts like an abrasive on your cylinder and wears it quickly. This is exactly the case.
I wish you to quickly build a new aircraft for the Stalker 66.

Regards,Ruslan

Thanks for the kind words and information regarding fuel, I will make that change for the next one!

Don

Michael Palm

Quote from: Ruslan Kurenkov on December 31, 2018, 02:39:14 AM
Hello Target
The company Stalker never produced engines with the designation .55
Regards,Ruslan

Hello mr Kurenkov. I have friend in Finland, Alf Lindholm that has a Stalker 55. And when i lookd around the internet i found this :http://www.stalker-modusa.com/index3.htm  Is that a different company?
R/C is disco, C/L is Rock n Roll

Ruslan Kurenkov

#21
Quote from: Michael Palm on December 31, 2018, 09:13:24 AM
Hello mr Kurenkov. I have friend in Finland, Alf Lindholm that has a Stalker 55. And when i lookd around the internet i found this :http://www.stalker-modusa.com/index3.htm  Is that a different company?
Hello Michael
I meant that Stalker did not produce an engine with the designation 55 under its own brand and in a separate case. This engine was produced under the Modusa (Made in USA) brand for the American company and in the 61 engine crankcase with a reduced piston size.
Also under the Modusa brand, Stalker produced the engine with the designation 35 in one crankcase with engines 40 and 46 with plain bearings. But it was a long time ago, more than 15 years ago. These engines (35 and 55) were produced in small experimental batches and did not have a demand for which they were discontinued. They did not go to the series. So serially, in large quantities, Stalker did not produce the engine with the designation 55 exclusively under his own brand.

Regards,Ruslan

Ruslan Kurenkov

Quote from: Motorman on December 31, 2018, 09:41:29 AM
.049 not 0.49
Hello Motorman !
Why do you need such a small engine? This is a very very small engine. Very tiny! I think it would be a very nice gift for collectors. It is a pity, but such small engines in the near future Stalker will not produce. Very sorry! Happy New Year to you and all the best!

Regards,Ruslan

Michael Palm

Quote from: Ruslan Kurenkov on December 31, 2018, 09:35:44 AM
Hello Michael
I meant that Stalker did not produce an engine with the designation 55 under its own brand and in a separate case. This engine was produced under the Modusa (Made in USA) brand for the American company and in the 61 engine crankcase with a reduced piston size.
Also under the Modusa brand, Stalker produced the engine with the designation 35 in one crankcase with engines 40 and 46 with plain bearings. But it was a long time ago, more than 15 years ago. These engines (35 and 55) were produced in small experimental batches and did not have a demand for which they were discontinued. They did not go to the series. So serially, in large quantities, Stalker did not produce the engine with the designation 55 exclusively under his own brand.

Regards,Ruslan

Thank You for making that clear!
R/C is disco, C/L is Rock n Roll

M Spencer

QuoteIs your new aircraft in the photo a copy of a real airplane?





This ones 57 in. ST 21/40 . / HP 40 R P R . built 2000 .
Conceived 1976 , bigger one is 66 in span .  FOLKERTS SK3 . By Jupiter .





My 66 is STAMPED 66 . Got Via Brian Eather Via Kaz Minato . Brian says is the first 66 made ? .

Thanks .  H^^



Advertise Here