News:



  • April 26, 2024, 07:51:51 AM

Login with username, password and session length

Author Topic: Ringmaster Plans ...  (Read 4368 times)

Offline Pepper Kay

  • Trade Count: (0)
  • New Pilot
  • *
  • Posts: 10
Ringmaster Plans ...
« on: October 02, 2006, 08:19:35 AM »
Hi All:

Need a source for Ringmaster plans - want the 42" original ...

Thanks,

Pepper
AMA #3937
Pepper Kay
Garland, TX
AMA # 3937

Offline Shawn Kuntz

  • Trade Count: (0)
  • Lieutenant
  • ***
  • Posts: 121
  • Ringmasters Forever!
Re: Ringmaster Plans ...
« Reply #1 on: October 02, 2006, 08:41:57 AM »
Try Barry Baxters Control Line Plans Service.  He has one.
http://www.controllineplans.com/index.htm
Shawn Kuntz
Bismarck, North Dakota USA

Offline Oregon_Flyer

  • ACE
  • Trade Count: (0)
  • Commander
  • ****
  • Posts: 192
Re: Ringmaster Plans ...
« Reply #2 on: October 02, 2006, 03:22:11 PM »
Hi Pepper,

I have Baxter's S-6 Super Ringmaster plans [plane logo next to my status on posting info at left side of posting's is a photo of that plane, also have pic's posted on photo gallery.  The plans are straight foreward however there is no construction guide.  Also, pay attention to the ribs as there is a layout error that I am not sure Barry fixed even though I emailed him about it.  The plans are crisp and dead bang accurate, not some kinkos xerox jobs that are questionable at best.  The plane flies extremely well and I have no regrets in building it.  If you are an experienced builder, I would suggest you consider an adjustable leadout setup and carved out balsa wing tips.  Also, there are a couple of methods for installing weight boxes/tubes for adjusting the CG and outboard wing tip weight.  I mention this because depending on the wheels and other changes you may make, the ability to adjust the balance points becomes real important.  If there are any issues that come to mind, either post them on the building tips or email me.

Marv

Offline Pepper Kay

  • Trade Count: (0)
  • New Pilot
  • *
  • Posts: 10
Re: Ringmaster Plans ...
« Reply #3 on: October 02, 2006, 04:05:02 PM »
Hi marv:

I just went to Barry's site and did not see an S6 - also, couldn't find any photos of yours ...

Can you help ?? ...

Thanks,

Pepper
AMA #3937
Pepper Kay
Garland, TX
AMA # 3937

Offline Tom Perry

  • Trade Count: (0)
  • Captain
  • *****
  • Posts: 424
Re: Ringmaster Plans ...
« Reply #4 on: October 02, 2006, 05:05:50 PM »
Hi All:

Need a source for Ringmaster plans - want the 42" original ...

Thanks,

Pepper
AMA #3937

Pepper,

Bill Schmidt draws some of the best plans I've ever seen.  I bought Ringmaster S1 plans from him and am very happy with them.  I believe they were $10.00.  He sent me the full size plans he draws, a copy of the plans by Sterling (not full size), and a list of other plans he creates.

Contact:

Bill Schmidt
4647 Krueger
Bel Aire, KS 67220
(316) 744-0378           #^ ~> #^
Tight lines,

Tom Perry
 Norfolk, Virginia

Offline Oregon_Flyer

  • ACE
  • Trade Count: (0)
  • Commander
  • ****
  • Posts: 192
Re: Ringmaster Plans ...
« Reply #5 on: October 03, 2006, 02:28:16 PM »
Hi Pepper

Here is some info for you,

Link to Baxter's "Super Ringmaster"

http://www.controllineplans.com/frameset2.htm

As you can see, it is listed on page 2 under the stunt catagory and titled Super Ringmaster.

As for photos of my "Ring"  home page [first page to load] lower left is a button that says
photo gallery  mine is on page two it is yellow and white.

Marv










Advertise Here
Tags:
 


Advertise Here