News:



  • May 22, 2024, 06:12:49 AM

Login with username, password and session length

« previous next »
Pages: [1]   Go Down

Author Topic: New Fox NVA???  (Read 700 times)

Offline wwwarbird

  • 2016 supporter
  • Trade Count: (0)
  • Admiral
  • *
  • Posts: 7987
  • Welcome to the Stunt Hanger.
New Fox NVA???
« on: September 20, 2010, 07:27:00 PM »
 I was just over on Fox's website. Have they finally updated their C/L NVA assemblies? The .35 Stunt in their ad photos show a nice looking new setup. If so, this could be a great improvement.
Logged
Narrowly averting disaster since 1964! 

Wayne Willey
Albert Lea, MN U.S.A. IC C/L Aircraft Modeler, Ex AMA member

Offline Marvin Denny

  • Trade Count: (0)
  • Captain
  • *****
  • Posts: 889
  • Welcome to the Stunt Hanger.
Re: New Fox NVA???
« Reply #1 on: September 21, 2010, 10:37:42 AM »
  That has been out now for about a year.  Yes it IS new (for Fox), and it IS better for some (a few) applications.  It does adjust quite nicely, but cannot be reversed for inverted applications.  It is quite weighty for a NVA, and to get to the LH front motor mount bolt, the NVA must be loosened and the fuel inlet nipple rotated up out of the way.  I have several and am currently not using any of them due to the above mentioned problem areas

  Bigiron
Logged
marvin Denny  AMA  499

Offline wwwarbird

  • 2016 supporter
  • Trade Count: (0)
  • Admiral
  • *
  • Posts: 7987
  • Welcome to the Stunt Hanger.
Re: New Fox NVA???
« Reply #2 on: September 21, 2010, 06:41:46 PM »
 Good to know Big, thanks for the info. y1 Is there a nut to hold it like normal or is it pressed in?
Logged
Narrowly averting disaster since 1964! 

Wayne Willey
Albert Lea, MN U.S.A. IC C/L Aircraft Modeler, Ex AMA member

Offline Jim Thomerson

  • Trade Count: (0)
  • Admiral
  • ******
  • Posts: 2087
Re: New Fox NVA???
« Reply #3 on: September 21, 2010, 06:48:08 PM »
I use the Fox needle valve assemblies made in Italy.   VD~
Logged

Offline wwwarbird

  • 2016 supporter
  • Trade Count: (0)
  • Admiral
  • *
  • Posts: 7987
  • Welcome to the Stunt Hanger.
Re: New Fox NVA???
« Reply #4 on: September 21, 2010, 07:28:31 PM »
 HA! Me too actually, just snooping around is all. ;D
Logged
Narrowly averting disaster since 1964! 

Wayne Willey
Albert Lea, MN U.S.A. IC C/L Aircraft Modeler, Ex AMA member

Offline Marvin Denny

  • Trade Count: (0)
  • Captain
  • *****
  • Posts: 889
  • Welcome to the Stunt Hanger.
Re: New Fox NVA???
« Reply #5 on: September 22, 2010, 08:51:35 AM »
  It is held in by a nut.  A 1/4th inch wrench or socket fits the nut.

  Bigiron
Logged
marvin Denny  AMA  499

Advertise Here
Pages: [1]   Go Up
« previous next »
Tags:
 


Advertise Here