Author Topic: thinning epoxy (Read 1060 times)

t michael jennings · « **on:** February 13, 2008, 06:46:40 PM »

Many times epoxy is used to fuel proof the engine compartment.

What is the best fluid to thin 5 minute and 30 minute epoxy.

1. denatured alcohol

2. lacquer thinner

3. acetone

t michael jennings

Bill Little · « **Reply #1 on:** February 13, 2008, 07:02:38 PM »

I prefer Z-Poxy straight up! But if not, I use acetone and lacquer thinner both, which ever one my hand grabs. Never tried the denatured alcohol.

Will Hinton · « **Reply #2 on:** February 13, 2008, 07:13:46 PM »

The alchy works fine, but it takes very little to do the job. I, too, prefer the Z-Poxy staright up. I apply it with a brush and then wipe it back off with a paper towel. I check it after curting and sometimes feel the need to repeat the process, but usually don't have to.
Blessings,
Will

Bill Little · « **Reply #3 on:** February 13, 2008, 07:17:14 PM »

Quote from: Will Hinton on February 13, 2008, 07:13:46 PM

The alchy works fine, but it takes very little to do the job. I, too, prefer the Z-Poxy staright up. I apply it with a brush and then wipe it back off with a paper towel. I check it after curting and sometimes feel the need to repeat the process, but usually don't have to.
Blessings,
Will

I acid brush it on and use a heat gun to thin it out (Z-Poxy). Uses a lot less that way and soaks into the wood very nicely.

Dick Fowler · « **Reply #4 on:** February 13, 2008, 07:38:42 PM »

I ran across this about three years ago... pretty good stuff regarding thinning epoxy.

http://www.seqair.com/skunkworks/Glues/WestSystem/Thinning/Thinning.html

Randy Powell · « **Reply #5 on:** February 13, 2008, 10:39:46 PM »

I don't thin it. At least not directly. I heat it. Heat up the components before mixing and it paints on like water. Works for me.

Richard Edwards · « **Reply #6 on:** February 17, 2008, 01:01:16 AM »

when you thin 6 minute or even 30 minute epoxy doesnt that make it start to set and go sticky rather fast I know if I want epoxy to dry fast I hold the item in front of a heat source to get it to set faster??

Dzlstunter · « **Reply #7 on:** February 17, 2008, 08:12:21 AM »

Quote from: Dick Fowler on February 13, 2008, 07:38:42 PM

I ran across this about three years ago... pretty good stuff regarding thinning epoxy.

http://www.seqair.com/skunkworks/Glues/WestSystem/Thinning/Thinning.html

This is a very good reference. Thanks, Dick

Alan Hahn · « **Reply #8 on:** February 17, 2008, 10:22:17 AM »

I use the heat gun method. Paint it on, heat it up the firewall area, let the hot drops move around and seep into the grain, then let it drip off. It will then setup faster.

Author Topic: thinning epoxy (Read 1060 times)

t michael jennings

thinning epoxy

Bill Little

Re: thinning epoxy

Will Hinton

Re: thinning epoxy

Bill Little

Re: thinning epoxy

Dick Fowler

Re: thinning epoxy

Randy Powell

Re: thinning epoxy

Richard Edwards

Re: thinning epoxy

Dzlstunter

Re: thinning epoxy

Alan Hahn

Re: thinning epoxy