News:



  • May 13, 2024, 08:26:34 AM

Login with username, password and session length

Author Topic: what line length?  (Read 1265 times)

Offline Glenn (Gravitywell) Reach

  • Gravitywell
  • 2016 supporter
  • Trade Count: (0)
  • Admiral
  • *
  • Posts: 1391
what line length?
« on: September 01, 2011, 06:46:55 PM »
I am building a White Lightning by Bruce Feaver and am putting a Brodak .061 on it.  My question is, what line length should I use?  I have a set of .008x52' braided lines....are they too long? H^^
Glenn Reach
Westlock, Alberta
gravitywell2011 @ gmail . com

Offline ray copeland

  • 24 supporter
  • Trade Count: (0)
  • Captain
  • *
  • Posts: 871
Re: what line length?
« Reply #1 on: September 01, 2011, 08:17:30 PM »
Glenn, your question is basically how powerful is the brodak .061. I am not qualified to comment on that. But, my slightly oversized White Lightning flies very well for a flat winger with a norvel .061 on 45 foot 30lb. spiderwire lines.  The .008 braided lines were just too much of a hassle for me.
Ray from Greensboro, North Carolina , six laps inverted so far with my hand held vertically!!! (forgot to mention, none level!) AMA# 902150

Offline minnesotamodeler

  • 2014 Supporters
  • Trade Count: (0)
  • Admiral
  • *
  • Posts: 2335
  • Me and my Chief Engineer
    • Minnesotamodeler
Re: what line length?
« Reply #2 on: September 01, 2011, 09:43:38 PM »
I fly most all my .061-powered planes on 48' of Spiderwire.  I do fly my combat wings with .061s on 42', just for the adrenalin rush.  Lap times, and perception, is about equivalent to 120-mph Fast ships on 60' lines.  Mind, these are Norvels and one Wasp.  Don't know how the Brodak compares.
--Ray 
Roseville MN (St. Paul suburb, Arctic Circle)
AMA902472

Online Larry Renger

  • 21 supporter
  • Trade Count: (0)
  • Admiral
  • *
  • Posts: 4000
Re: what line length?
« Reply #3 on: September 01, 2011, 09:45:42 PM »
I would try the 52' lines with a great deal of caution.  I think 45' is about right, or even a bit long.  However, it is easier to cut lines down, than add to them.... :##

If you fly conservatively, you should be able to safely cut them down a bit at a time until the plane flies solidly at the ends no matter what the maneuver.
Think S.M.A.L.L. y'all and, it's all good, CL, FF and RC!

DesignMan
 BTW, Dracula Sucks!  A closed mouth gathers no feet!

Offline Glenn (Gravitywell) Reach

  • Gravitywell
  • 2016 supporter
  • Trade Count: (0)
  • Admiral
  • *
  • Posts: 1391
Re: what line length?
« Reply #4 on: September 01, 2011, 10:54:20 PM »
OK....I'll fly the plane on 52' and cut them down as needed.  Thanks fellas.  Now for something else....what wing tip weight?  One nickle or two? ;D
Glenn Reach
Westlock, Alberta
gravitywell2011 @ gmail . com

Online Larry Renger

  • 21 supporter
  • Trade Count: (0)
  • Admiral
  • *
  • Posts: 4000
Re: what line length?
« Reply #5 on: September 02, 2011, 08:45:12 AM »
On sheet wings, I put a bolt through the wing and just add or subtract washers as needed.
Think S.M.A.L.L. y'all and, it's all good, CL, FF and RC!

DesignMan
 BTW, Dracula Sucks!  A closed mouth gathers no feet!

Offline minnesotamodeler

  • 2014 Supporters
  • Trade Count: (0)
  • Admiral
  • *
  • Posts: 2335
  • Me and my Chief Engineer
    • Minnesotamodeler
Re: what line length?
« Reply #6 on: September 02, 2011, 03:28:19 PM »
One nickel oughtta do.  I use a penny on smaller .049 models.
--Ray 
Roseville MN (St. Paul suburb, Arctic Circle)
AMA902472

Offline Wayne Collier

  • Trade Count: (0)
  • Captain
  • *****
  • Posts: 503
Re: what line length?
« Reply #7 on: September 14, 2011, 12:23:14 PM »
        Why waste a nickle when you can get a good washer for only 7 cents (plus tax).   :-\
Wayne Collier     Northeast Texas
<><

never confuse patience with slowness never confuse motion with progress


Advertise Here
Tags:
 


Advertise Here