News:



  • March 28, 2024, 03:15:40 PM

Login with username, password and session length

Author Topic: Smoothest Finish on a Profile Fuselage  (Read 1886 times)

Offline Mike Griffin

  • 2018 Supporter
  • Trade Count: (0)
  • Admiral
  • *
  • Posts: 2754
Smoothest Finish on a Profile Fuselage
« on: August 29, 2022, 10:20:51 AM »
What method have you used to get the smoothest finish on a profile fuselage before painting? 

Mike

Online Dennis Nunes

  • 23 supporter
  • Trade Count: (0)
  • Commander
  • *
  • Posts: 363
Re: Smoothest Finish on a Profile Fuselage
« Reply #1 on: August 29, 2022, 11:34:31 AM »
Hi Mike,

I use Z-Poxy Finishing Resin. Apply to the wood and scrape off and wipe with paper towel. Sand and repeat. Spray with Harbor Freight grey primer, sand off primer and then paint.


Dennis

Offline Mike Griffin

  • 2018 Supporter
  • Trade Count: (0)
  • Admiral
  • *
  • Posts: 2754
Re: Smoothest Finish on a Profile Fuselage
« Reply #2 on: August 29, 2022, 11:52:14 AM »
Thank you Dennis.  Does this pretty much eliminate the wood grain?

Mike

Offline john e. holliday

  • 24 supporter
  • Trade Count: (0)
  • Admiral
  • *
  • Posts: 22752
Re: Smoothest Finish on a Profile Fuselage
« Reply #3 on: August 29, 2022, 12:04:03 PM »
Use light weight fibre glas with the epoxy. D>K
John E. "DOC" Holliday
10421 West 56th Terrace
Shawnee, KANSAS  66203
AMA 23530  Have fun as I have and I am still breaking a record.

Online Dennis Nunes

  • 23 supporter
  • Trade Count: (0)
  • Commander
  • *
  • Posts: 363
Re: Smoothest Finish on a Profile Fuselage
« Reply #4 on: August 29, 2022, 01:17:09 PM »
Thank you Dennis.  Does this pretty much eliminate the wood grain?

Mike
Yes. Whatever the Z-Poxy doesn't cover the gray primer will take care of the rest. Make sure to sand the majority of the gray primer off as it is heavy!

Attached are photos of my plane after spraying primer, what's left after sanding the primer and the finished plane.


Dennis


Offline Mike Griffin

  • 2018 Supporter
  • Trade Count: (0)
  • Admiral
  • *
  • Posts: 2754
Re: Smoothest Finish on a Profile Fuselage
« Reply #5 on: August 29, 2022, 04:10:55 PM »
Yes. Whatever the Z-Poxy doesn't cover the gray primer will take care of the rest. Make sure to sand the majority of the gray primer off as it is heavy!

Attached are photos of my plane after spraying primer, what's left after sanding the primer and the finished plane.


Dennis

That looks really good Dennis.

Mike

Offline Gary

  • Trade Count: (0)
  • New Pilot
  • *
  • Posts: 2
Re: Smoothest Finish on a Profile Fuselage
« Reply #6 on: November 24, 2022, 06:51:24 PM »
What type of paint do you use over the zpoxy that's fuel prof

Online Dennis Nunes

  • 23 supporter
  • Trade Count: (0)
  • Commander
  • *
  • Posts: 363
Re: Smoothest Finish on a Profile Fuselage
« Reply #7 on: November 24, 2022, 08:22:35 PM »
What type of paint do you use over the zpoxy that's fuel prof
Hi Gary,

For bare wood, after apply the Z-Poxy and sanding smooth, I spray with Harbor Freight gray automotive primer. I seal the gray primer with RANDOLPH: 9701 CLEAR BUTYRATE TAUTENING DOPE.

For the base color (white) all my planes are done using RANDOLPH: Q-1050-BQ COLORED NON-TAUTENING BUTYRATE DOPE. Trim colors use same type of dope different color.

For the clearcoat I used CERTIFIED COATINGS: Part# 09-10500 MFR Model# CCP-B182-RG.

All products are available from Aircraft Spruce & Supply Co. https://www.aircraftspruce.com/


Dennis


Dennis

Online doug coursey

  • Trade Count: (0)
  • Commander
  • ****
  • Posts: 207
Re: Smoothest Finish on a Profile Fuselage
« Reply #8 on: November 24, 2022, 08:41:26 PM »
Use light weight fibre glas with the epoxy. D>K
USE 3/4 OZ CLOTH...IT HARDLY WEIGHS ANYTHING....I USE CLEAR DOPE AND TALCUM POWDER FOR FILLER
AMA 21449

Offline MikeyPratt

  • Trade Count: (0)
  • Captain
  • *****
  • Posts: 748
Re: Smoothest Finish on a Profile Fuselage
« Reply #9 on: November 26, 2022, 02:37:20 PM »
Mike,
Lots of good suggestions and I’m sure they will all work,  what I’ve been doing is using Glass-Coat clear onto the bear balsa and wiping it off as much as possible with paper towels.  When the paint cures sand with 220 grit sandpaper, then apply a second coat Glass-coat again wipe off with paper towels.  When cured, sand again the 220 and you will notice that the grain is filling really fast, now you can use silkspan, Glass Cloth, or some primer to finish it off. 

I’ve used the Z proxy before and it didn’t penetrate into the balsa as well as the Glass-coat epoxy paint did, consequently making the balsa much stronger for close to the same weight.

To paint the colors is a breeze, you can use anything you like that is fuel proof, dope, epoxy, don’t use any thing with enamel is it.  I’ve used this same precess on carrier and racing models and it works great.

Later,
Mikey

Online doug coursey

  • Trade Count: (0)
  • Commander
  • ****
  • Posts: 207
Re: Smoothest Finish on a Profile Fuselage
« Reply #10 on: November 26, 2022, 06:06:38 PM »
i have thinned epoxy with acetone and it penetrates the wood more than just epoxy unthinned,it also slows down the drying process too.
AMA 21449

Online Dennis Toth

  • 2020 supporter
  • Trade Count: (0)
  • Admiral
  • *
  • Posts: 4209
Re: Smoothest Finish on a Profile Fuselage
« Reply #11 on: November 27, 2022, 06:34:35 AM »
I have used one cost of medium CA that I spread thin with a paper towel for first coat (only do one coat of this as more coats may take a long time to cure fully). This seals the wood and toughens it (let it gas off at least overnight), then cover with either 3/4oz glass or silkspan using clear dope. Three coats of clear then one coat of clear with zinc stearate (Randy Smith Aero 1, ~ 1 tablespoon for 8oz clear dope). Sand lightly with 220 then 3-4 coat of clear it should be ready for block coat paint (I use SIG - Dianna Cream).

Best,   DennisT


Advertise Here
Tags:
 


Advertise Here