News:

 

CLICK HERE--><--CLICK HERE

Trim for lower level flight

Started by Dennis Toth, December 13, 2010, 09:32:40 AM

Previous topic - Next topic

0 Members and 3 Guests are viewing this topic.

Dennis Toth

Guys,
I have a pretty well trimmed 46 size ship, it groove nicely and has good tension throughout. One area that I would like to improve is the height of the level flight groove. This ship seems to settle in at 8ft both upright and inverted. I can push it down to 5ft but to do that I need to fly it to that level. I have tried adjusting the handle with more down and this cause it to fly lower upright but requires serious concentration inverted. Is there any trims that could be applied that will lower the natural groove?

Best,           DennisT

Dennis Toth

#1
Phil,
I understand what you are saying, my problem isn't flying inverter nor do I have a fear of flying close to the ground. What I was getting at was this ship hits a groove both upright and inverted at 8ft. If I pull in the down a tweak it will push it down while upright but inverted it then requires over coming the now slight up that the handle setting put in.

I fly with my handle straight up and down, no bias. The ship is balanced at 24% back from the LE of the average cord. The wing is 18% thickness with normal sweep. Tail is around 17% of wing area. It seems to me that if the ship seems to naturally hit the same natural altitude upright and inverted the trim change needs to affect both, that's what I am looking for.

Best,         DennisT

Steve Fitton

If you figure it out let me know.  My new plane does the exact same thing, wanting to fly level at 6 or 7 feet both upright and inverted.  Its almost like having to force it down against ground effect, but its too high to be that.  My old plane is the polar opposite, you have to hold it up to keep it from drifting below 5 feet both ways.  Its puzzling.
Steve

Randy Powell

What's your alignment like: engine, wing and stab centerline? Any down thrust dialed in? How about stab incidence?
Member in good standing of P.I.S.T
(Politically Incorrect Stunt Team)
AMA 67711
Randy Powell

Bill Little

Good question, and one that needs a better "trimmer" than I am to answer.  But, I don't think a handle adjustment is the way to go.  That forces you to accommodate the handle setting when you are in inverted.  You don't want to have to do that.  Down thrust "might" do the same thing to an otherwise trimmed out plane.  The plane will want to sink up right, but climb inverted with either solution to my understanding.

I am awaiting answers!  I want to learn about the cure. ;D
Big Bear <><

Aberdeen, NC

James Hylton Motorsports/NASCAR/ARCA

AMA 95351 (got one of my old numbers back! ;D )

Trying to get by

Mark Scarborough

You may think I am whacked, but IMHO I would add a half ounce nose weight. I have had two planes that when they were trimmed, ( well trimmed to me anyway) would want to fly high in level, One I fixed with handle adjustment. the other when I did that made the level flight assymetrical,  adding a half ounce to the nose worked both upright and inverted. and yes I know this will affect other areas of trim.
For years the rat race had me going around in circles, Now I do it for fun!
EXILED IN PULLMAN WA
AMA 842137

Jim Thomerson

This is very strange.  I adjust the airplane to fly the same height in level flight upright and inverted with the handle. Thinking about it, this ends up with the airplane flying where I wanted it to fly, even though the "where" is different for OTS and modern stunt.  My airplanes tend toward nose heavy anyway.  I'm interested to learn more and will pay more attention to what I am doing as well.

Bill Little

Quote from: Mark Scarborough on December 13, 2010, 01:14:10 PM
You may think I am whacked, but IMHO I would add a half ounce nose weight. I have had two planes that when they were trimmed, ( well trimmed to me anyway) would want to fly high in level, One I fixed with handle adjustment. the other when I did that made the level flight assymetrical,  adding a half ounce to the nose worked both upright and inverted. and yes I know this will affect other areas of trim.

No Mark,  not "whacked"....... maybe a *little* unbalanced........ ???  LL~ LL~

You might be on to something.  That nose weight would not tend to lead to asymmetrical problems.
Big Bear <><

Aberdeen, NC

James Hylton Motorsports/NASCAR/ARCA

AMA 95351 (got one of my old numbers back! ;D )

Trying to get by

Dennis Toth

Guys,
I think the nose weight is part of the answer but this ship holds it's line when the motor is cut. If it were to tail heavy I would expect it to jump up at motor cut off, if nose heavy it would drop slightly, it does neither. Could be that a little nose weight will help.

Alignment is 0-0-0. No downthrust, small rudder offset (1/8") no stab incidence.

I have been reading some threads on this and also thought back to my trainer ship way back in 1956. That ship had a 3/4oz chunk of lead on the tip, it flew what seemed like 20' off the ground in level flight (lots of air for my uncle to grab the handle when needed). I'm starting to think that this ship might need a very small reduction in the tip weight. The ship doesn't hinge during squares or hard loops so I think it is close. To get down only a few feet might be the difference of 1/8 oz or so. Anyone have this experience?

Best,         DennisT

Mark Scarborough

Quote from: Bill Little on December 13, 2010, 02:38:36 PM
No Mark,  not "whacked"....... maybe a *little* unbalanced........ ???  LL~ LL~

You might be on to something.  That nose weight would not tend to lead to asymmetrical problems.

The clue to me is that if the plane flies the same altitude upright and inverted, then its not likely a handle adjustment, if it flies at different altitudes then I try adjusting the handle first.
My goal is to hold my handle naturally and achieve level 5 foot flight,,

( for what its worth, Randy Powell will pop in here and say that I never fly that low,, you watch,, HB~>
For years the rat race had me going around in circles, Now I do it for fun!
EXILED IN PULLMAN WA
AMA 842137

Bill Little

Quote from: Mark Scarborough on December 13, 2010, 02:54:04 PM
The clue to me is that if the plane flies the same altitude upright and inverted, then its not likely a handle adjustment, if it flies at different altitudes then I try adjusting the handle first.
My goal is to hold my handle naturally and achieve level 5 foot flight,,

( for what its worth, Randy Powell will pop in here and say that I never fly that low,, you watch,, HB~>

Yeah, Mark, we agree.  It is simply a matter of the model in question doing the same thing upright AND inverted.  A handle adjustment wouldn't cure that, in my experiences......

And I don't think that Dennis' idea of tip weight would cure it, since the wings are not out of "whack".  And he says it's not hinging. ;D
Big Bear <><

Aberdeen, NC

James Hylton Motorsports/NASCAR/ARCA

AMA 95351 (got one of my old numbers back! ;D )

Trying to get by

dale gleason

Somewhere, perhaps the "Scared Kitten" construction article?  Bill Netzeband addressed this problem. I think he flew a few laps with his eyes closed and then looked to see where the plane was tracking, upright and inverted.....then he told what he did to fix it.

I'm not making this up, but I can't recall where I saw it.

"Tonto not quite put finger on".

dg

Bill Little

Quote from: dale gleason on December 13, 2010, 03:15:46 PM
Somewhere, perhaps the "Scared Kitten" construction article?  Bill Netzeband addressed this problem. I think he flew a few laps with his eyes closed and then looked to see where the plane was tracking, upright and inverted.....then he told what he did to fix it.

I'm not making this up, but I can't recall where I saw it.

"Tonto not quite put finger on".

dg

Hi Dale,

If you are speaking of the "eyes closed" deal, I can believe that. 

After watching combat pilots never watching their OWN plane during a match, I can see how one would be able to close their eyes and fly.

I ain't up to trying it though! LL~ LL~
Big Bear <><

Aberdeen, NC

James Hylton Motorsports/NASCAR/ARCA

AMA 95351 (got one of my old numbers back! ;D )

Trying to get by

Mark Scarborough

Hey Bill, I will try it for ya,,
with YOUR airplane of course  ;D
For years the rat race had me going around in circles, Now I do it for fun!
EXILED IN PULLMAN WA
AMA 842137

Randy Powell

My point was if something is out of alignment, it can cause a tendency for the plane to "prefer" a certain flight level or attitude.
Member in good standing of P.I.S.T
(Politically Incorrect Stunt Team)
AMA 67711
Randy Powell

Eric Viglione

Sounds like handle to me... I can't picture a plane the size we fly getting into ground effect so high at 8ft...

Since we are all pretty good at mentally compensating for upright level flight, I usually use inverted flight, and horizontal round eights and overheads to tell me whats going on with the handle instead.

When inverted, does it feel like you are fighting to keep the plane out of the ground, (feeding down, which is up inverted) ? Chances are you need to shorten the down line. (try small increments, 1/8" at a time or so)

In your eights, is your outside loop hard to keep from being taller than your inside? Insides tighten up? Again, different symptom, same problem, shorten your down line.

Overheads, same question, same answer.

Do you bobble or overcontrol your insides? same answer...

I'm skewing the examples all to one side here, but it works the other way too obviously.

Any who, those are the kinda things I look for.

Hope it helps,
EricV

Howard Rush

Quote from: stuntguy13 on December 13, 2010, 02:48:47 PM
I'm starting to think that this ship might need a very small reduction in the tip weight.

On my airplane, reducing the tip weight cured a tendency to dive when flying inverted.  I don't understand it, but it worked.
The Jive Combat Team
Making combat and stunt great again

Steve Helmick

#17
"Ted's Rule" is to put the CG at the same percentage of the MAC as the horizontal tail area (i.e., 17% in this case). It might take more than 1/2 oz, but remember that 17%'s a starting point, not an ironclad regulation! You'll be moving the LO's forward the same amount, I hope.  H^^ Steve

"The United States has become a place where professional athletes and entertainers are mistaken for people of importance." - Robert Heinlein

In 1944 18-20 year old's stormed beaches, and parachuted behind enemy lines to almost certain death.  In 2015 18-20 year old's need safe zones so people don't hurt their feelings.

Mark Scarborough

Quote from: Randy Powell on December 13, 2010, 05:44:54 PM
My point was if something is out of alignment, it can cause a tendency for the plane to "prefer" a certain flight level or attitude.
Randy, I dont disagree on that,,
For years the rat race had me going around in circles, Now I do it for fun!
EXILED IN PULLMAN WA
AMA 842137

Mark Scarborough

Quote from: Eric Viglione on December 13, 2010, 06:17:29 PM
Sounds like handle to me... I can't picture a plane the size we fly getting into ground effect so high at 8ft...

Since we are all pretty good at mentally compensating for upright level flight, I usually use inverted flight, and horizontal round eights and overheads to tell me whats going on with the handle instead.

When inverted, does it feel like you are fighting to keep the plane out of the ground, (feeding down, which is up inverted) ? Chances are you need to shorten the down line. (try small increments, 1/8" at a time or so)

In your eights, is your outside loop hard to keep from being taller than your inside? Insides tighten up? Again, different symptom, same problem, shorten your down line.

Overheads, same question, same answer.

Do you bobble or overcontrol your insides? same answer...

I'm skewing the examples all to one side here, but it works the other way too obviously.

Any who, those are the kinda things I look for.

Hope it helps,
EricV
Eric, in most cases I would agree, but he states it flies the same upright and inverted
For years the rat race had me going around in circles, Now I do it for fun!
EXILED IN PULLMAN WA
AMA 842137

Eric Viglione

Oh, I missed that, and I re-read the thread before I posted too... long threads get me like that sometimes, sorry.

If it does it upright and inverted, well, that's a good trick! All I can envision is some kind of tail heavy condition with a little too much slop in the controls, where the the tail drops against the slop and holds an attitude when your hand is comfortably neutral... and does the same thing in the other direction when inverted, taking up the slop in the controls the other way.

Other than that, it's above my pay grade. Looking forward to hearing what you eventually find to be the cause, if you ever do...

Thanks,
EricV

john e. holliday

In my opinion it is the pilot not the airplane.  If the airplane flies the same upright and inverted it is the pilot.  Especially if it flies the pattern the way you want it to.  No slacking of the lines or dropping wing tips.  For several flights do only two maneuvers, upright and inverted flight only.  Drop that arm until you are at the altitude you want.  Then go  inverted and do the same.  I think someone referred to it as muscle training as well as the mind.  Don't do any loops or other maneuvers until you get yourself trained to the altitude you want to fly.  Once you can take off doing a full lap to get to altitude then maybe throw in a maneuver.  I know  it gets boring, right coach, same as doing laps on the football field.  Try it and see if it don't work. H^^

PS:As was told in a stunt clinic, when practicing and fuel tank is large enough, do three reverse wing overs with two laps between each before continuing the pattern.  But, then you have to remember to only do one in copetition.jeh
John E. "DOC" Holliday
10421 West 56th Terrace
Shawnee, KANSAS  66203
AMA 23530  Have fun as I have and I am still breaking a record.

Howard Rush

Quote from: Bill Little on December 13, 2010, 04:54:46 PM
After watching combat pilots never watching their OWN plane during a match, I can see how one would be able to close their eyes and fly.

I just noticed this item from a few months ago and thought I should post a picture of something I saw at the 2008 world champs.  This lady from Khazakhstan is flying an F2D model so jumpy that I have trouble aiming one while looking at it.  She's not looking at hers, and she's flying it upside-down.
The Jive Combat Team
Making combat and stunt great again

phil c

You might try holding your handle a foot or so lower and see if that brings it down.  If it does, then I'm with Eric, there is too much slop in the controls and by the time you get it out(with handle movement) the flaps are drooped a degree or so and produce enough lift to bring the plane up.

If you want to see some neat flying, look up the last combat world champs on You Tube.  One flight shows the eventual champion doing pretty respectible reverse wingovers down to no more than ten feet behind his back while looking down at the ground.
phil Cartier

proparc

Based solely on what you saying Stuntguy13, our "Mr. Little" got it right. Thats handle baby!!
Milton "Proparc" Graham

Tag

Advertise Here