stunthanger.com

General control line discussion => Open Forum => Topic started by: Matt Neumann on November 01, 2024, 12:56:16 PM

Title: sponge sanding blocks.
Post by: Matt Neumann on November 01, 2024, 12:56:16 PM
I noticed some sponge sanding blocks at the hardware store.  These blocks are a sponge with with a rough surface for sanding.  They are typically used for sanding drywall compound.  The finest I found was 150 grit.  This would be fine for basic shaping.  Anyone know of a finer grit version?  What brand and what grit?  Ideally your 320 grit or even 400 would be nice.  These to me would be wonderful for the sheeted wings that I am doing.  You could sand and not worry about flat spots because they seem to have just enough give to keep from getting flat spots but still act as a block.
Title: Re: sponge sanding blocks.
Post by: Steve Berry on November 01, 2024, 01:04:59 PM
I don't know of any, off hand, but something similar that could be used are cork sanding blocks and pads. I've seen them online but haven't had a chance to test them myself.

Steve

Sent from my SM-N986U using Tapatalk

Title: Re: sponge sanding blocks.
Post by: Dave_Trible on November 01, 2024, 01:26:21 PM
Matt Home Depot and Lowes have them down to 220 or greater.  Then most auto parts stores have them on down to 400 and foam sanding pads all the way to 5000.   I remember you telling me there maybe wasn't a Depot or Lowes in your city so maybe you better go right to Advance or O' Reilly auto parts.

Dave
Title: Re: sponge sanding blocks.
Post by: bill stavros on November 01, 2024, 10:04:44 PM
Have you tried any auto body and paint suppliers. They usually have these items.
Title: Re: sponge sanding blocks.
Post by: Dave Harmon on November 02, 2024, 01:03:33 PM
In the past I have used a piece of spongy foam...like upholstery foam rubber.
Then put sandpaper around the foam and used the palm of my hand to move it around.
Works great for surfaces that are already flat.
Title: Re: sponge sanding blocks.
Post by: Will Hinton on November 02, 2024, 06:37:31 PM
the real beauty of these sponge sanding pads is the tendency to sand through on corners and ribs is greatly reduced, I've used them both on my planes and in the guitar shop for many years and refuse to be without them, so go gettem Matt!
Title: Re: sponge sanding blocks.
Post by: Peter in Fairfax, VA on November 02, 2024, 09:33:26 PM
I saw 220 and 320 at Lowes:  https://www.lowes.com/pd/3M-SandBlaster-Pro-2-5-in-x-4-5-in-320-Grit-Commercial-Sanding-Sponge/3746783 (https://www.lowes.com/pd/3M-SandBlaster-Pro-2-5-in-x-4-5-in-320-Grit-Commercial-Sanding-Sponge/3746783)
Title: Re: sponge sanding blocks.
Post by: Peter in Fairfax, VA on November 02, 2024, 09:36:10 PM
Even 1000 https://www.lowes.com/pd/Gator-SilicaCut-Grit-Premium-Sanding-Sponge-3-in-x-5-in/5013732891 (https://www.lowes.com/pd/Gator-SilicaCut-Grit-Premium-Sanding-Sponge-3-in-x-5-in/5013732891)