stunthanger.com
General control line discussion => Open Forum => Topic started by: Paul Taylor on August 31, 2014, 07:29:45 AM
-
I was just tacking something up and CA'ed the wood to my finger. That always happens but as soon as I feel it I pull it off. Well last night I could not pull it off. I did not feel it and held it in place then felt it start to burn. It felt like it was going to pull skin off. So I tried soaking it in acetone. No go! Put it on the belt sander. That did the trick. 😜
Sent from my iPhone using Tapatalk
-
Paul,
They make a "release" agent just for things like that. The agent, simple liquid chemicle, can also be used to remove any part attached with CA.
Comes in handy.
-
Pics(http://tapatalk.imageshack.com/v2/14/08/31/b8faea0cdd64b6d7bbf55156a3355da7.jpg)
(http://tapatalk.imageshack.com/v2/14/08/31/754a2d7b3ba7efa08f6131b7f8975ce7.jpg)
Sent from my iPhone using Tapatalk
-
Hi Paul,
The belt sander sounds a little risky!
For what it's worth, 15 to 30 seconds in nitro methane will soften CA so it can be eailsy pulled apart.
In fact I believe that the comercial de-bonder sold by Tower and others is only Nitro Methane!
Safer than a belt sander!
Randy Cuberly
-
You can just wait a while -- CA only bonds to skin for a while, then it peels off.
When I do something like that I trim the hunk down with a modeling knife (TRIM, don't try to cut it off), or maybe sand it a bit with a HAND sanding block. Then later in the day or the next morning I pull it off.
-
Sometimes you can't sand it off if you glue fingers together. I find acetone works better than nitro. Soak a Q tip in acetone and keep pulling the edge as you keep it wet. Don't pull too hard and rip the skin. Takes a few minutes but it works.
MM
-
Holy Crap Paul!!!
Hey Ya'll watch this!!!
I'm going to send you some debonder.
-
I woulda thought there'd be an iPhone APP for that. LL~ Steve
-
Next time try a fingernail file instead of the belt sander. Not near as much chance of getting a new nickname like Nubby, Klutzo or my personal favorite Three Finger Jack. Where I work they call me Dangit but I don't wanna talk about it:-)
-
I woulda thought there'd be an iPhone APP for that. LL~ Steve
There is. It's called stunt hangar.
-
You can just wait a while -- CA only bonds to skin for a while, then it peels off.
When I do something like that I trim the hunk down with a modeling knife (TRIM, don't try to cut it off), or maybe sand it a bit with a HAND sanding block. Then later in the day or the next morning I pull it off.
thats all well and good except that will be the night the wifey feels amorous,,, then what LOL
-
thats all well and good except that will be the night the wifey feels amorous,,, then what LOL
It all depends where you stuck the wood... >:D
-
I had a nearly full bottle of thin "buildit" that got stuck in my hand....thing is, I fell backwards on my stool, and was grabbing everything trying not to break the part I was gluing. Well, I couldn't get the bottle out of my hand...all 4 fingers and my thumb were stuck. This would never have happened if the applicater tip hadn't come off....talk about getting hot...!!! After I finally got to my feet, I straight away got my other hand stuck. I started to pry my shoe off....then I thought better of it. We used nearly a whole bottle of my wife's fingernail polish remover before the plastic turned loose. The whole label was stuck in my right palm. LL~