stunthanger.com

General control line discussion => Open Forum => Topic started by: Brian Gardner on September 10, 2024, 03:46:51 AM

Title: Enya 35 (5224) & 45 (6001) ABC sets
Post by: Brian Gardner on September 10, 2024, 03:46:51 AM
Hi All,

Just testing the waters so to speak - would there be much interest in me doing ABC piston/liner/rod/pin sets for either the Enya 35 (5224) and Enya (6001)?

Don't get me wrong - I'm still way behind and can't keep up with production of all the current motors...this is more a bit of forward lanning.

Brian

Title: Re: Enya 35 (5224) & 45 (6001) ABC sets
Post by: Gordon Tarbell on September 10, 2024, 06:18:32 AM
Yes and yes
Title: Re: Enya 35 (5224) & 45 (6001) ABC sets
Post by: M Spencer on September 10, 2024, 11:11:05 PM
Finally ran the FP 40 Liner , in the FSR .40 .

12 heat cycles , then dragged a Magnum thru a breeze . Was shutting off downhill , which a stock FSR wont do .
Early Days yet - but looking good . In the Caudron now .

One needs to relieve the top of the backplate , to clear . Which shows the Timing could go down , dropping the liner .
Havnt Measured to see how much . Recomended for any FSR 40 opperator . The B. G.  FP 40 P/L set up .

45 FSR sets timed at 130 - 110 wouldnt be a bad idea . Theyd fit Magnum GP 44s too , without the piston / trans port .

Only gotta Enya 29 & 45 .
Title: Re: Enya 35 (5224) & 45 (6001) ABC sets
Post by: Motorman on September 11, 2024, 10:12:03 PM
Dropping the liner would be limited by the piston height vs stroke not stroke and skirt length vs back plate diameter.
Title: Re: Enya 35 (5224) & 45 (6001) ABC sets
Post by: Brian Gardner on September 12, 2024, 01:25:33 AM
This thread is about whether people want me to make sets for the Enyas. Keep it relevant.
Title: Re: Enya 35 (5224) & 45 (6001) ABC sets
Post by: GERALD WIMMER on September 12, 2024, 04:43:07 AM
Hello We have three Enya 45 6001's on models currently and a 35 ,they are all very good stunt engines from the factory. An ABC set up would probably preform a lot better then the twin ring versions, with less drag and probably run cooler . I would buy a couple of sets.

Thanks Brian for helping keep our old engines running better then ever!

Regards Gerald
Title: Re: Enya 35 (5224) & 45 (6001) ABC sets
Post by: Martin Quartim on September 18, 2024, 01:24:58 PM
I will take one of each. There are 2 Enya 45 6001, the plain bearing Iron P/L and the 45 BB 6001 with Aluminum Piston Ring. The block seems to be the same but I am not sure if the P/L have the same fit for both.

What I really want is an ABC set for my Enya SS50.


Martin
Title: Re: Enya 35 (5224) & 45 (6001) ABC sets
Post by: Brian Gardner on September 18, 2024, 06:13:30 PM
Hi Martin,  I have added you to the list. The 45 that I am using for sample/measurement purposes is a 6001 45BB twin ball bearing. I don't have a plain bearing version to compare compatibility.

For any engine/new project I need sufficient orders to do a production run of more than 20 units. So I can't help you with the SS50 at this point sorry.


Quote from: Martin Quartim on September 18, 2024, 01:24:58 PM
I will take one of each. There are 2 Enya 45 6001, the plain bearing Iron P/L and the 45 BB 6001 with Aluminum Piston Ring. The block seems to be the same but I am not sure if the P/L have the same fit for both.

What I really want is an ABC set for my Enya SS50.


Martin
Title: Re: Enya 35 (5224) & 45 (6001) ABC sets
Post by: Philip THOMAS on September 30, 2024, 08:54:35 PM
Hell yeah.
I値l take two sets for the Enya 35; one I値l wear around my neck as jewellery and the other I値l fly.
Title: Re: Enya 35 (5224) & 45 (6001) ABC sets
Post by: Brian Gardner on October 01, 2024, 02:54:24 AM
I have added you to the list.

Brian

Quote from: Philip THOMAS on September 30, 2024, 08:54:35 PM
Hell yeah.
I値l take two sets for the Enya 35; one I値l wear around my neck as jewellery and the other I値l fly.