Author Topic: Does anyone know where to get one of these?? (Read 1719 times)

ptg · « **on:** May 05, 2012, 05:03:42 PM »

Once upon a time in my travels I picked up one of these prop adapters. Looks pretty standard but has 2 unique features.

1. Collet shaft is steel
2. Collet shaft is tapped for 3mm bolt

Other specs:
Fits 5mm motor shaft
Shaft diameter and thread for prop nut is 6mm

This adapter is a clean, elegant solution for my new plane. Would sure like to get more of them but can’t remember source. Anybody know??

Thanks,
PTG

Dennis Adamisin · « **Reply #1 on:** May 05, 2012, 10:54:39 PM »

PTG
Found a listing for a Maxx Products adapter, part #ACC370 that is made for a 5mm motor shaft and has a 6mm prop shaft - hard to do that unless it is in steel? Unfortunately there are no pix, but you might be able to contact them and get the story.

http://www.maxxprod.com/mpi/mpi-291.html#Prop.%20Adapters

Otherwise, maybe TruTurn?

Igor Burger · « **Reply #2 on:** May 06, 2012, 01:21:50 AM »

I did such thing myself from scorpion adapter, but actually I have similar on OS max motor, but I am not sure with outer thread ... that inner is m3

Darkstar1 · « **Reply #3 on:** May 06, 2012, 10:20:47 AM »

PTG
I believe thats a 5 mm adapter from a Hacker motor. Depending on the motor that was bought they gave you an
aluminum or steel one. Those adapters have a 6 mm prop shaft because I have one. The OS adapters are a bit larger where the prop goes and you'll find if you tighten a OS adapter they are hard to get off without some kind of modified gear puller. Any website that has Hacker accessories should have them. The first pic is the Hacker . The second is the OS .

Darkstar1 · « **Reply #4 on:** May 06, 2012, 10:51:05 AM »

Dennis,
Tru-Turn only makes aluminum shaft adapters. The one I have fits the 5 mm shaft but the prop shaft is 8 mm but requires the backplate to be reamed to .4375 in and another adapter ring made up to tighten the motor shaft.

ptg · « **Reply #5 on:** May 06, 2012, 11:07:56 AM »

Thanks Darrell,

That's the one! Guess I didn't remember where I got it because it came with the motor (or that's my story and I'm stickin' to it

).

PTG

Darkstar1 · « **Reply #6 on:** May 07, 2012, 03:24:22 PM »

Ty,
I modified a Battery puller I got from a auto parts store. Any of the chain stores should have one. It works in a pinch But I would still rather find one that's purpose made. My guess would Snap-on or MAC Tools but I haven't
looked around yet.

ptg · « **Reply #7 on:** May 07, 2012, 09:04:17 PM »

Hey Darrell and Ty,

One good turn deserves another. Here is your collet puller. It's made by Hyperion. Comes in two sizes, 5/6mm shaft size and 8mm size.

Cheers,
PTG

Darkstar1 · « **Reply #8 on:** May 08, 2012, 04:58:00 AM »

Looks good Phil, Thanks.

Darkstar1 · « **Reply #9 on:** May 08, 2012, 03:37:17 PM »

Ty
Try this web site.
http://www.allerc.com/hyperion-collet-adapter-puller-for-m5-and-m6-adapters-p-2732.html
Just ordered one and It's on the way.

Author Topic: Does anyone know where to get one of these?? (Read 1719 times)

ptg

Does anyone know where to get one of these??

Dennis Adamisin

Re: Does anyone know where to get one of these??

Igor Burger

Re: Does anyone know where to get one of these??

Darkstar1

Re: Does anyone know where to get one of these??

Darkstar1

Re: Does anyone know where to get one of these??

ptg

Re: Does anyone know where to get one of these??

Darkstar1

Re: Does anyone know where to get one of these??

ptg

Re: Does anyone know where to get one of these??

Darkstar1

Re: Does anyone know where to get one of these??

Darkstar1

Re: Does anyone know where to get one of these??