Author Topic: Tiger 60 (Read 3413 times)

Bootlegger · « **on:** July 23, 2011, 06:18:08 AM »

Guy's I posted thei in the engine section also, I am looking for head shims that will fit the S T 60.
Any suggestions as to what will inner change?
Thanks a lot, Gil

john e. holliday · « **Reply #1 on:** July 23, 2011, 08:27:17 AM »

Get the tool from Lee's Machine Shop and make your own shims. Jim Lee is on here once in a while.

W.D. Roland · « **Reply #2 on:** July 23, 2011, 09:51:30 AM »

Or a quick trip to the hardware store and you can have 100s made before lunch.
Thats a little over an hour from now.

Bootlegger · « **Reply #3 on:** July 23, 2011, 11:34:15 AM »

W D how about 'splanin' what you r referin' 2???

W.D. Roland · « **Reply #4 on:** July 23, 2011, 11:36:50 PM »

Gil
Called you but you were out.
Left # in case lost.

Will be around most of Sunday, Town on Monday

Dallas Hanna · « **Reply #5 on:** July 24, 2011, 01:09:19 AM »

Gee you blokes jump all over the place asking these questions.

I left you this a couple of days ago on SSW for the same question but you gave no reply as yet!

> Guy's I am looking for the bore of the Tiger 60 as I need
>some head shims that will interchange with it.
> Any suggestions?
> Thanks a lot, Gil

24mm or 0.945"

HH

PJ Rowland · « **Reply #6 on:** July 24, 2011, 01:33:06 AM »

Herb - I need a PA 75 can you machine me one?

Dallas Hanna · « **Reply #7 on:** July 24, 2011, 01:57:09 AM »

Quote from: PJ Rowland on July 24, 2011, 01:33:06 AM

Herb - I need a PA 75 can you machine me one?

Too cold in the workshop to machine anything PJ although Matt Colan and Dave Fitz have been working on me.

Have got to do some bits for Matt before spending some more of the kids inheritance on a trip to the UK Aug/September. Can you stop sending that cold weather north!

All the best
HH

W.D. Roland · « **Reply #8 on:** July 24, 2011, 02:07:35 AM »

Quote from: Dallas Hanna on July 24, 2011, 01:09:19 AM

Gee you blokes jump all over the place asking these questions.

I left you this a couple of days ago on SSW for the same question but you gave no reply as yet!

> Guy's I am looking for the bore of the Tiger 60 as I need
>some head shims that will interchange with it.
> Any suggestions?
> Thanks a lot, Gil

24mm or 0.945"

HH

Redundancy, old NASA trick.

No Blokes down South.....

Geoff Goodworth · « **Reply #9 on:** July 24, 2011, 02:51:04 AM »

I second Herb's request PJ. I hurt my fingers just getting my Dremel out of the router table yesterday.

On the other hand, we could sure use some of that global warming that people keep talking about.

PJ Rowland · « **Reply #10 on:** July 24, 2011, 04:44:20 AM »

Stop whining.. I just returned from USA where it never got below 30 C .. now im stuck in crappy Melbourne and im freezing..

Steven Kientz · « **Reply #11 on:** July 24, 2011, 06:43:41 AM »

Pj
It got even hotter in central Indiana since you left. Will gladly trade our weather for yours.

Steve

PJ Rowland · « **Reply #12 on:** July 24, 2011, 07:36:44 AM »

Someone else said that to me today..

Nope.. I will trade 110 F for 30 F + rain anyday

Howard Rush · « **Reply #13 on:** July 24, 2011, 08:42:17 PM »

Temperature at our flying field is forecast to get up to 70 degrees F (21 C) tomorrow. I may need a short-sleeve shirt.

Brett Buck · « **Reply #14 on:** July 24, 2011, 08:51:30 PM »

Quote from: PJ Rowland on July 24, 2011, 04:44:20 AM

Stop whining.. I just returned from USA where it never got below 30 C .. now im stuck in crappy Melbourne and im freezing..

You stop whining, too. I left the NATs where is it was 95 every day, and went to visit my parents - where it was 104 (40C in French) every day. With higher humidity, too.

Brett

Matt Colan · « **Reply #15 on:** July 24, 2011, 09:07:55 PM »

During the winters here in Vermont, I've seen temperatures on our thermometer reach -33.4 degrees F. During summer, it just recently hit 98 so I have a very large temperature range to live in!

Quote from: Dallas Hanna on July 24, 2011, 01:57:09 AM

Too cold in the workshop to machine anything PJ although Matt Colan and Dave Fitz have been working on me. Have got to do some bits for Matt before spending some more of the kids inheritance on a trip to the UK Aug/September. Can you stop sending that cold weather north!

All the best
HH

Yea Dallas, how about that hardware?

James Mills · « **Reply #16 on:** July 24, 2011, 09:11:57 PM »

Quote from: Brett Buck on July 24, 2011, 08:51:30 PM

You stop whining, too. I left the NATs where is it was 95 every day, and went to visit my parents - where it was 104 (40C in French) every day. With higher humidity, too.

Brett

Brett,

Did you tell me once that your parents live in Arkansas?

James

Dallas Hanna · « **Reply #17 on:** July 24, 2011, 09:24:21 PM »

Quote from: Matt Colan on July 24, 2011, 09:07:55 PM

During the winters here in Vermont, I've seen temperatures on our thermometer reach -33.4 degrees F. During summer, it just recently hit 98 so I have a very large temperature range to live in!
Yea Dallas, how about that hardware?

Scratching around the workshop to find the alloy for you Matt! Just warming up a bit here now as PJ is hopefully keeping the cold air "down in Mexico"! We're 600 miles north but it still gives us below freezing in the mornings at times.

HH

Brett Buck · « **Reply #18 on:** July 24, 2011, 09:37:33 PM »

Quote from: James Mills on July 24, 2011, 09:11:57 PM

Did you tell me once that your parents live in Arkansas?

Hot Springs, right on the lake. Heat index for July 13 - 116 deg.

Brett

PJ Rowland · « **Reply #19 on:** July 25, 2011, 07:21:40 AM »

mm im getting warm and toasty just thinking about that Brett

Bootlegger · « **Reply #20 on:** July 28, 2011, 06:10:56 AM »

Thanks for the helpGuy's