stunthanger.com

General control line discussion => Classifieds => Topic started by: Bill Morell on July 29, 2021, 07:22:57 PM

Title: WTB Os Max 19 prop driver
Post by: Bill Morell on July 29, 2021, 07:22:57 PM

Looking for a 1964 OS Max 19 prop driver.

Title: Re: WTB Os Max 19 prop driver
Post by: Dan McEntee on July 29, 2021, 09:07:39 PM

  Bill, I think I have one older MAX .19 and will check the drive washer. That vintage of engine had the drive washers with the D shaped hole. You may get lucky and one from something lese may fit, like even one from a LA.25. It's over 100 degree heat index still here at 10PM but a cold front is supposed to be going through tonight. When it cools off up in the attic tomorrow I'll check it out. They made a .19, .20 an .25 back then that may be candidates.
  Type at you later,
   Dan McEntee

Title: Re: WTB Os Max 19 prop driver
Post by: Bill Morell on July 29, 2021, 09:50:14 PM

Thanks Dan!

Title: Re: WTB Os Max 19 prop driver
Post by: Dan McEntee on July 29, 2021, 10:04:41 PM

  I had an older MAX .25 handy and a FP-20-40 drive washer and it fits the .25. The steel drive washer fits also. I would have to think the same would fit the .19, but I'll know for sure tomorrow.
  Type at you later,
    Dan

Title: Re: WTB Os Max 19 prop driver
Post by: Air Ministry . on July 29, 2021, 10:11:53 PM

Airsail in N Z had a bag with about 200 new ones in it . 50 or 100 anyway . maybe a kiwi knows where they went ? .

Title: Re: WTB Os Max 19 prop driver
Post by: Dan McEntee on July 30, 2021, 10:11:55 AM

   Well, it was cooler in the attic today so checked it out. The MAX .19 I have is smaller than expected. The OS .20-.40 prop drive washer is too big  and will not work. I checked against the same vintage MAX .15 and that will work. I don't have any spares of either, or at least haven't found any yet. This at least gives you another option.
  Type at you later,
    Dan McEntee

Title: Re: WTB Os Max 19 prop driver
Post by: Bill Morell on July 30, 2021, 10:57:05 AM

I appreciate it Dan. I knew the 15 would fit but forgot to mention it.

Title: Re: WTB Os Max 19 prop driver
Post by: Bill Morell on August 02, 2021, 10:27:53 AM

Still looking.

Title: Re: WTB Os Max 19 prop driver
Post by: Bill Morell on August 06, 2021, 09:38:43 AM

Bump

Title: Re: WTB Os Max 19 prop driver
Post by: Bill Morell on August 18, 2021, 05:30:15 PM

Anyone out there?

Title: Re: WTB Os Max 19 prop driver
Post by: Dan McEntee on August 18, 2021, 08:30:39 PM

  I came up empty. I think since the .19 is so hard to find, a .15 parts engine might be your best bet for the prop driver. Maybe shoot at email to that eBay seller Bob Brooks, shuttrman in eBay. He may have something that crosses over. I would try Randy Smith also, since he as been dealing in OS parts for so long
  Type at you later,
    Dan McEntee

Title: Re: WTB Os Max 19 prop driver
Post by: Bill Morell on August 19, 2021, 10:04:20 AM

Already tried shtterman,  no luck.

Title: Re: WTB Os Max 19 prop driver
Post by: Bill Morell on August 26, 2021, 08:35:43 AM

Bump

Title: Re: WTB Os Max 19 prop driver
Post by: Fred Constantine on August 27, 2021, 02:19:55 PM

I may have what you need. Check out the photos.  If it is, PM me with you address.
Fred

Title: Re: WTB Os Max 19 prop driver
Post by: Bill Morell on September 03, 2021, 01:59:12 PM

Fred came through with the right stuff! The search is over!