Here is a link to the SH thread.  Jan  Holuszko makes them. I have bought a couple and they are little gems.

 http://stunthanger.com/smf/index.php?topic=14865.0

Duke, there's a couple more on E-Bay for not much more than I paid.
                                                                                                  James

I wonder if at least the needle and spray bar are still available from doug. I could probaby come up with my own delrin venturi if necessary.

Hi fred-
I might just do that. 
And thank you for your offer to send the TD collars. I'm likely to take you up on the offer. Not to save money, but to liberate and use some poor unused parts, as they were meant to be. I know you get it.
Happy holidays to you and yours,  Fred.

V/r,
Target

Sent DG an email....
I'll let you know if I need the TD collars/needles, Fred.
You have at least 3, right?

Excellent. I'll need one for converting my os .26 fs to stunt as well as the two wasps i have coming.
Enjoy the holiday today.

Is the AP Wasp .061 off the primary market already?

Yep. 
There are a few NIB hoarded by the hobby king guy, and he lets a few out on ebay occasionally.
I'd almost rather get the NV Big Migs, since they come in a u/c version already.

Doug Galbreath graciously converted two of my AP Wasp 061's (yes, purchased through the hated auction site).  Doug does truly amazing work.  Doug has the added benefit of making and stocking 1/2A NVAs.  I cleaned and shipped the two motors stock, then Doug fabricated the venturis and installed them with two of his new NVAs.  The results are beautiful.

Attached (hopefully) is a picture of the two motors after conversion.

Paul W.

You might be special to Doug, or you had great timing. See below.

Chris just ask him

http://www.the-printer.net/DookCat.html

Asked him and the answer was that he was out of those NVA's and doesn't intend on making any more.
Looks like it's the TD venturi/adapter arrangement, or possibly pushing out the needle from a cox plastic backplane and using that....

I'll PM you about the TD NVA's you have offered when I come to a conclusion.

Happy Turkey day!

Chris I just spent an hour on CEF looking for Ken Cooks various methods with the Norvels....no luck

I am sure you have seen the adaptation for the fine thread NVAs for combat with bladder

One of Ken's creative adapters was need to use a Cox Venturi and TeeDee standard or KK Fine thread NVA
To do this he shaped DOWN a APC prop hub to sleeve into the engine throat tight fit
The drilled and tapped for the Cox Venturi
The J&B the adapter into the engine

The three brass TeeDee NVAs I have are all standard thread
If you want to use fine thread push through NVA... some can be pushed out of back plates on the reedies or bought from Texas Timers

I have never held a ASP wasp but they sure look like a Norvel clone to me

No worries, gents-

I have a friend of mine that has been properly bribed with fresh swordfish, tuna, rock cod, and lingcod and has thus agreed to make the needed two (plus one spare, I hope) delrin adapters for me.... Finally work meets the hobby again in my life, yay.

So I will just need 3, (4 if possible, to have one spare) of the TD normal 80tpi collars from you Fred, and I will buy the venturies separately. Let me know what I can give you for them. I have some RC swag, that you could be interested in. Miniature Berg 7ch 72Mhz rx's? Servos, lots of variety? Other stuff as well.

The great thing is that I just got some bare intake manifolds for the OS.26 4c I wanted to convert, and it looks like the ID is smaller than the #3 drill size that the 1/4"-32 tap requires, so all I have to do is squarely cut that intake at the head side of the carb barrel, and tap it to fit the TD venturi. Then just screw the venturi in, (no adapter required, a beautiful thing!) and I will be all set for a U/C setup on the OS.26.

R,
Target

You got it, Fred!

Kind regards,
Target